Page Comparison

Panel

borderColor	#3D3D3D
bgColor	#F4F4F4
titleColor	#3D3D3D
borderWidth	0
titleBGColor	#3D3D3D
borderStyle	solid

ON THIS PAGE

Table of Contents

indent	20px

Insert excerpt

	BrightScript Version Navigation Menu
	BrightScript Version Navigation Menu
nopanel	true

This object supports receiving arbitrary Infrared remote control codes using the NEC and RC5 protocols.

Object Creation: The roIRReceiver object is created with an associative array.

Code Block
CreateObject("roIRReceiver", config As roAssociativeArray)

The associative array can contain the following parameters:

source: A string value indicating the source of the input.
- "IR-in": The 3.5mm IR input/output connector (available on 4Kx42 and XDx32 models)
- "GPIO": Pin 1 of the GPIO connector
- "Iguana": The Iguanaworks IR transceiver. This source can support both NEC and RC5 encodings simultaneously.
encodings: An array indicating the required encodings.
- "NEC"
- "RC5" (supported on the Iguanaworks IR transceiver only)

NEC codes are expressed in 24 bits:

Bits 0-7: Button code
Bits 8-23: Manufacturer code

Note

title	Note

If the manufacturer code is zero, then the code is considered to be intended for the Roku SoundBridge remote control.

The roIRReceiver object can generate the following events:

roIRDownEvent: Generates when a button is pressed.
roIRRepeatEvent: Generates when a button repeats.
roIRUpEvent (Iguanaworks IR transceiver only): Generates when a button is released.

ifUserData

SetUserData(user_data As Object)

Sets the user data that will be returned when events are raised.

GetUserData() As Object

Returns the user data that has previously been set via SetUserData(). It will return Invalid if no data has been set.

ifMessagePort

SetPort(port As roMessagePort)

Specifies the port that will receive events generated by the roIRReceiver instance.

Example

To connect your USB-C port to an IR receiver:

Code Block

'12-53-23 - V1.x12 Test IR input, output to system log
 
Sub Main()

	m.scriptlog = CreateObject("roSystemLog")	   'display messages in system log
	m.Eventloop = Eventloop
	m.msgPort = CreateObject("roMessagePort")
	m.gpioPort = CreateObject("roGpioControlPort")
	m.gpioPort.SetPort(m.msgPort)
  	
	m.configIR = CreateObject("roAssociativeArray")
	'Built-in IR via usb c
	s.configIR.source = "TypeC"
	m.configIR.encodings = CreateObject("roArray", 1, false)
	m.configIR.encodings[0] = "NEC"
	m.IRRecep = CreateObject("roIRReceiver", m.configIR)
  	
	if (type(m.IRRecep) = "roIRReceiver") then
		m.
    IRRecep.SetPort(m.msgPort)
		m.
    scriptlog.SendLine((" @@@@ Please press a button on remote control to display IR code... ")
	else if m.IRRecep = invalid then
    		m.scriptlog.SendLine((" @@@@ IR receiver not detected, Please connect IR receiver and reboot player... ")
	end if
  	
	m.Eventloop(msgport)
 
End Sub
 
 
Sub Eventloop(msgport as object)
    scriptlog = CreateObject("roSystemLog")
	   'display messages in system log
    while true
		
        event = wait(0, m.msgPort)
		m.
        scriptlog.SendLine("@@@@ Received event"+ ";type(event))	
		  
        if (type(event) = "roIRDownEvent") then			
				       
                IrData$ = StripLeadingSpaces(stri(event))
				m.
                scriptlog.SendLine((" @@@@ "+IrData$)
		
        end If		
	    
    End while
end Sub

Note that LS424 is the only platform where IR input is supported on the Type C connector. Also, a special cable is required: either an adapter (3.5mm plug to 3.5mm socket crossover), or custom all-in-one cable (LiteOn PN 306300009327).

Versions Compared

Old Version 3

New Version Current

Key