...
...
| title | Table of Contents |
|---|
| Expand | ||||||||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
| ||||||||||||||
|
...
| Code Block |
|---|
nc = CreateObject("roNetworkConfiguration", 0)
rebootRequired = nc.SetupDWS()
if rebootRequired RebootSystem() |
Setting the Password
By default, the DWS is enabled with the player serial number as password. To set a custom password with digest authentication, use the roNetworkConfiguration object:
...
Reset Password (Local DWS only): Set a new password for DWS authentication on the local network.
Reboot Player: Reboot the player remotely.
Reboot with Crash Report: Reboot the player and save a crash-report file to the "brightsign-dumps" folder. BrightSign support may request the crash report when helping you troubleshoot the player.
Factory Reset: Reset the player to factory defaults, erasing all persistent registry settings for networking, security, and other applications.
Recovery URL: Set a new recovery URL, which is used by the player to retrieve setup information if there is an autorun-related failure.
DWS Access: Enable/disable DWS access on the local network.
Reprovision Device: Allows the player to fall back toB-Deployand retrieve the setup package saved for the player, or to use the "Default Setup" package if no package exists for the player.
SD / MicroSD / MSATA / USB
| Anchor | ||||
|---|---|---|---|---|
|
...
Network Configuration: View extensive information about network interface settings.
Network Diagnostics: Run network diagnostics. This process may take some time to complete, especially when certain tests fail.
DNS Lookup: Test the specified DNS address to check whether name resolution is working.
Ping: Ping a device with the specified IP address or DNS name.
Trace Route: Perform a standard traceroute diagnostic on the specified IP/DNS address. Check the Resolve IP Addresses box to resolve the specified DNS name.
Network Neighborhood: Display information on the current network neighborhood.
Network Packet Capture: Allows the capture and collection of live network packet data from the network interfaces connected to the BrightSign player.
Disable Autorun: Force the player to reboot and disable the autorun script when the device restarts. This allows the unit to display the firmware version and IP address on screen (if the unit is connected to a local network). If the player has a serial port, you will be able to access the system shell over a null-modem serial cable.
Format Storage: Takes you to the Format Storage page, which allows you format storage devices attached to the player.
Storage: Select a storage device. You can only format storage devices that are currently unformatted; storage that already contains content files or autorun scripts cannot be reformatted.
File system: Select a supported file system to use when formatting the storage device.
Telnet/SSH: Allows you to enable Telnet and SSH for your player. This lets you access the BrightSign application console when serial port (the default I/O for the application console) is inaccessible. Not that we do not recommend enabling either Telnet or SSH in a production environment for security reasons. A Port Number can be set for Telnet, and a Port Number and SSH Password can be set for SSH as shown in the image below:
...
This page provides several diagnostic tools related to the video settings of the player:
HDMI Status: Whether the each player HDMI connection (indicated as HDMI-1, HDMI-2, etc.) is “Active” or “Inactive”
Current Video Mode: The video resolution currently being output by the playeroutput on each HDMI connection (indicated as HDMI-1, HDMI-2, etc.). If the player is set to a 4K video mode, this field will also indicate whether the10-bit colorspace and/or HDR (high dynamic range) is currently being output.
Power Save: Disables HDMI output, the syncs for VGA output, and/or the DAC output for component video for each HDMI connection (indicated as HDMI-1, HDMI-2, etc.). The absence of a signal will cause some monitors to go into standby mode.
EDID Information: Displays the EDID data returned from a monitor one or more monitors attached to the player’s HDMI portsHDMI ports (indicated as HDMI-1, HDMI-2, etc.). This information can be copied and pasted into a text editor.
Change Video Mode: Changes the display mode/resolution of the player on all video outputs (HDMI®, VGA, and Component). The device will reboot and disable the current autorun script (similar to the Disable Autorun button in the Diagnostics tab). Otherwise, the autorun script will reset the video mode of the player by default.that
Advanced
Registry Dump: View a print out of all registry settings on the player.BrightSign OS Update: Instruct the player to download a .bsfw firmware-update file from the specified URL. After the file has been downloaded, the player will reboot and update its BrightSign OS version.
Storage Location: Enter the storage location and select View to temporarily access the player storage location.
BrightSign OS Logs: Select the level of detail you prefer in the BrightSignOS logs and then select Set to apply that setting.
Registry
The Registry tab allows you to view and edit the registry:
Registry
...
Select View Registry Dump to view the player
...
registry. You can copy the output to the clipboard or download it to a text file.
To submit registry commands, add registry entries, or delete registry entries, enter that information in the empty field under Command and then select Submit. You must reboot the player to see changes to the registry.
...
| Anchor | ||||
|---|---|---|---|---|
|