...
...
...
| borderColor | #3D3D3D |
|---|---|
| bgColor | #F4F4F4 |
| titleColor | #3D3D3D |
| borderWidth | 0 |
| titleBGColor | #3D3D3D |
| borderStyle | solid |
...
ON THIS PAGE
| Table of Contents | ||
|---|---|---|
|
This section describes the characteristics and operation of all connectors on the XD233 and XD1033.
Power Connector
The power connector for the XD233 and XD1033 is rated for 12V@3A. The plug is a right-side positive, locking 2-pin (1x2) connector.
3.5mm Serial
The UART (asynchronous serial) interface is a 3.5mm (1/8") jack
...
that uses RS-232
...
levels for communication. The receiver will tolerate input voltages between -30V and +30V, with anything below 3V interpreted as a logical 1. The transmitter drives +
...
8V for logical 0 and
...
-8V for logical 1.
| Note |
|---|
NoteXDx33 units that are rev H or later support full RS-232 signaling. The serial transmit pin on earlier versions of the XDx33 does not comply with voltage levels for RS-232 signaling (which requires a voltage below -3V for logical 1). In practice, the serial port can interoperate successfully with the majority of RS-232 receivers, but some devices (including some projectors and Crestron equipment) require strict conformance to RS-232 levels and will not accept 0V as logical 1. In these instances, you can connect the BrightSign player to the serial device using a USB-to-serial cable. |
The default baud rate of the RS-232 interface is 115200, with no parity, 8 data bits, and 1 stop bit. These settings can be configured in the software. The serial interface supports TX, RX, and ground only—RTS/CTS hardware flow control is not supported.A serial cable plug that is inserted into the 3.5mm jack should use the following signaling The following diagram illustrates the behavior of the TX and RX signal:
...
The 3.5mm serial port has the following configuration (from the perspective of the player):
Tip:
TransmitReceive
Ring:
RecieveTransmit
Sleeve: Ground
The following diagram illustrates the behavior of the TX and RX signal:
BrightSign players are DCE devices, so communication with another DCE device that uses a 3.5mm port would require a null-modem cable or converter that transposes the TX/RX signals. If the device communicating with the player is a DTE device with a DE9 serial port (performing asynchronous transmission), the serial cable should be wired as shown in the following diagram:
...
GPIO
The XD233 and XD1033 have a 12-pin GPIO switch and LED connector, which allows the player to control external LEDs or other devices requiring 24mA of current or less.
The GPIO port is a standard design manufactured by Phoenix Contact, Wurth Electronics, and others. The XDx33 series ships with two pluggable Pluggable GPIO terminal blocks , which can be inserted into the GPIO connector to make bare-wire contacts . An (see here for an example part number for these ). These terminal blocks can be found herepurchased from the BrightSign Store. If you wish to source your own terminal blocks, make sure to use 4-pin or 6-pin blocks (12-pin blocks are extremely difficult to remove from the GPIO port).
If you are using the GPIO connector to drive LEDs, connect the LED outputs to the LED ANODE and connect the LED CATHODE to the ground. If you want to connect another device, then the output is capable of sourcing or sinking up to 3.3V at 24mA, but there is a series resistor of 100W 100Ω in each line.
The connector GPIO also allows the for connecting of external contact closures to the ground. In order to connect a switch, connect one side of the switch to the switch input, and connect the other side to one of the ground pins on the GPIO connector. The connector can also supply 3.3V at up to 500mA to an external device. The 3.3V output is polyfuse-protected and can source up to 500mA.
If one BrightSign player is driving the inputs on another BrightSign player, then you can drive at most three inputs from one output. The following calculations explain this limitation:
| Note |
|---|
NoteThe GPIO outputs have 100W 100Ω series resistors; the GPIO inputs have 1K pullup resistors to 3.3V; and the input threshold is 2V high and .8V low. The high voltage is not problematic, but the low voltage can be if there are too many inputs connected to one output. |
1 out driving 1 in | V=3.3*100/(100+1,000)=0.3 |
1 out driving 2 in | V=3.3*100/(100+500)=0.55 |
1 out driving 3 in | V=3.3*100/(100+333.3)=0.76 |
1 out driving 4 in | V=3.3*100/(100+250)=.94 (This is too high, so 1 output driving 3 inputs is the maximum) |
The following table describes the pinout of the GPIO on the XT243 and XT1143:
Pin | Function | Pin | Function |
|---|---|---|---|
1 | GND | 7 | GND |
2 | 3.3V | 8 | 3.3V |
3 | BUTTON 0 | 9 | BUTTON 4 |
4 | BUTTON 1 | 10 | BUTTON 5 |
5 | BUTTON 2 | 11 | BUTTON 6 |
6 | BUTTON 3 | 12 | BUTTON 7 |
The following schematic illustrates the pinout of the GPIO connector.
...
RJ45 LAN
The XD233 and XD1033 have an RJ45 connector for 1000BASE-T networking. The maximum length for Cat 5E cable is 100 meters; the allowed length can be higher or lower depending on the quality of the cable.
USB
The XD1033 has two USB 2.0 ports: one Type A and one Type C. The Type A connector can act as a dedicated charging port (DCP) when the two data pins are shorted together, and the Type C connector can operate as either a host or a device (i.e. a dual-role port).
The Type-A connector can supply up to 1.5A of power for peripherals, while the Type-C connector can supply up to 1A. Note that these values are subject to a total current restriction of 2A for peripherals.
Both ports are capable of transfer speeds up to 480 Mbit/s. The maximum length for a USB cable is 5 meters.
The following table illustrates the pinout of the USB 2.0 Type A host port:
pin | Description | pin | Description |
|---|---|---|---|
1 | VBUS | 2 | D- |
3 | D+ | 4 | Ground |
The following table illustrates the pinout of the USB 2.0 Type C host port:
pin | Signal Name | Description | Mating Sequence | pin | Signal Name | Description | Mating Sequence |
|---|---|---|---|---|---|---|---|
A1 | GND | Ground return | First | B12 | GND | Ground return | First |
A2 |
B11 |
A3 |
B10 |
A4 | VBUS | Bus power | First | B9 | VBUS | Bus power | First |
A5 | CC1 | Configuration channel | Second | B8 |
A6 | Dp1 | Positive half of USB 2.0 differential pair – position 1 | Second | B7 | Dn2 | Negative half of USB 2.0 differential pair – position 2 | Second |
A7 | Dn1 | Negative half of USB 2.0 differential pair – position 1 | Second | B6 | Dp2 | Positive half of USB 2.0 differential pair – position 2 | Second |
A8 |
B5 | CC2 | Configuration channel | Second | ||||
A9 | VBUS | Bus power | First | B4 | VBUS | Bus power | First |
A10 |
B3 |
A11 |
B2 |
A12 | GND | Ground return | First | B1 | GND | Ground return | First |
3.5mm Audio Connector
The XD233 and XD1033 have a combination analog/optical audio jack. To To transmit a digital audio signal, use an a TOSLINK optical audio cable with a 3.5mm connector. Analog and digital audio cannot be transmitted simultaneously.
The full-scale voltage output of the analog audio is 2V RMS. The minimum load impedance is 32W32Ω.
The analog audio connector has the following pinout:
Tip: Left audio
Ring: Right audio
Sleeve: Ground for audio signal
3.5mm IR Input/Output
The IR blaster generates or receives a space-encoded NEC or Pronto Hex signal. The two transported bit values of the signal (0 and 1) are encoded using differing lengths of low-time IR pulses.
The 3.5mm IR in/out port has the following pinout:
Tip: 3.
3V3V@50mA
Ring: IR Input
Sleeve: IR Output
| Note | |
|---|---|
| title | NoteThe sleeve is used as a ground during input operations. |
HDMI Output
The HDMI-® out connector is used to send digital video and audio to HDMI-enabled sink devices. This connector is compatible with HDMI 2.0 devices, capable of outputting a maximum video resolution of 4096x2160x60p.
The following table illustrates the pinout of the HDMI connector:
pin | Description | pin | Description |
|---|---|---|---|
1 | TX2p | 2 | Ground |
3 | TX2n | 4 | TX1p |
5 | Ground | 6 | TX1n |
7 | TX0p | 8 | Ground |
9 | TX0n | 10 | TXCp |
11 | Ground | 12 | TXCn |
13 | CEC | 14 | NC |
15 | DDC SCL | 16 | DDC SDA |
17 | Ground | 18 | +5V DDC |
19 | HPD (Hot Plug Detect) | -- |